VEGO
A auto ranging digital multi-meter
Safety Instructions
To avoid possible electric shock, fire and personal injury, please read the safety instructions before use.
Shop link: https://shop.eimtechnology.com/collections/all-products/products/vego-digital-multimeter
Accessories

EZ-hook clips, allowing maximum of 10A current flowing through, ideal for educational experiments where you need to free hands for writing and recording.

Thermocouple, where you can place the probe (round head) onto a substance surface to measure its temperature; use a Kapton tape if necessary
Features
VEGO is a cell-battery powered multi-meter featured with auto-ranging electrical parameter measurements on a 4000 count LCD backlit display. The multiple measurement functions, including AC/DC Voltages, Currents, Resistance, Capacitance, Conductivity and Temperature, make VEGO an ideal tool for teaching, learning and debugging electrical and electronics related subjects. All VEGO packages contain additional set of high quality alligator clip wires to free your hands during testing and debugging.
Functions


LCD Screen
Displays numerical measurement results with corresponding units.
Specifications
LCD Display
4000 count
Range
Auto-ranging
Material
ABS/PVC
Sampling rate
3 times/second
True RMS
YES
Date holding
YES
Screen backlight
YES
Low power indicator
YES
Automatic power-off
YES
Dimension
120*60*33mm
Unit Weight
137.5g
Operation Conditions
Temp
0~40 °C
RH
<75%
Storage Conditions
Temp
-20~60 °C
RH
<80%
Measurement Modes
Rotating the Dashboard Knob to set VEGO to the desired measurement mode. There are 8 positions available from ‘a’ to ‘h’ as indicated in the figure below.

Position
Available Modes
Selection Method
a
Power off the device
N/A
b
DC voltage [0.4-600V]
AC voltage [0.4-600V]
AC voltage frequency
Automatic
Automatic
Press SEL once
c
DC voltage [0.04-400mV]
AC voltage [0.04-400mV]
AC voltage frequency
Automatic
Automatic
Press SEL once
d
Resistance [0.4Ω-40MΩ]
Diode forward biasing
Capacitance [4pF-4mF]
Conductivity [<50Ω]
Automatic
Press SEL once
Press SEL twice
Press SEL thrice
e
Temperature °C [-30-1000]
Temperature °F [-22-1832]
Automatic
Press SEL once
f
NCV [buzzer notification]
Automatic
g
DC current [0.4-10A]
AC current [0.4-10A]
Automatic
Automatic
h
DC current [0.04-400mA]
AC current [0.04-400mA]
Automatic
Automatic
Others
NCV (Non-contact Voltage)
VEGO has an internal magnetic sensor to detect the electromagnetic field of an AC voltage. In position f or NCV mode, the built-in buzzer will periodically sound while VEGO is in proximity of a AC voltage source (e.g. Line power). The buzzing frequency increases for higher AC voltage.
Current Measurement
In position g or [A] mode, the internal fuse can sustain 10A current for 10 seconds. To prevent blowing the fuse, DO NOT exceed 10A while measuring the current.
Automatic Power Off (APO)
By default setting, VEGO will trigger APO after 15 minutes of inactivity (the built-in buzzer will sound 5 times one minute before shutdown).
To resume the setting from APO, press SEL button so VEGO will resume back.
To disable APO, press and hold the SEL button first and then turn ON the device. The buzzer will sound 3 times to indicate the deactivation of APO.
Safety Instructions
When measuring, do not exceed the maximum measured value specified in the “Technical Specifications”.
Voltage below 36V is the safe voltage. When the voltage being measured is higher than 36V(DC) or 25V(AC), check whether the test leads are in reliable contact, are connected correctly, and are well insulated to avoid electric shock.
Attentions
Except for battery and fuse replacement, DO NOT attempt to repair the meter or change inner circuit; please contact our technical support directly
This product should NOT be stored or used under high temperature, high humidity, flammable, explosive and strong magnetic environments
Clean the case with a damp cloth and a mild detergent. DO NOT use corrosives or solvents
Turn OFF the meter before cleaning.
Remove the battery if you don’t use the device for long time
When the display shows
symbol, replace the batteries under the following steps:
- Unscrew the battery lid at the back
- Remove all batteries inside
- Replace new batteries of the same type
- Install the battery lid and fasten the screws
- Dispose the old batteries to proper recycle centers
- When replacing the fuse, please use the same size and type of fuse
Last updated
Was this helpful?